Vampire Collection

VAMPIRE CMHEX RCA Female Jack (w/Stripe), inside nut Designed to be the finest connector available. The CMHEX is gold plated with a Teflon dielectric. The CMHEX comes with a gold plated ground lug. Isolation washers are also included. It is designed to...

VAMPIRE SPD Gold-Plated Spade Lug 10/12awg These Spade Connectors from Vampire are gold-plated, over nickel-plated, over a brass base metal. DIY Tip: After crimping, slide the color coding over the connector extending onto the jacket of the cable. Use a...

VAMPIRE RG8 Gold-Plated (Copper Base) Spade Lug, 8awg (crimped) Gold plated step spade. Made from pure copper and designed to accept 8 gauge cables by crimping or soldering. Slide the color coding on the cable first, crimp or solder on the connector and...

VAMPIRE C7X Co-Axial RCA Male Plug (Satin), 7.3mm opening For 6.5-7.3mm diameter cables. Uses compression to insure proper RF shielding and strain relief. Slide nut on cable. Strip 3/4” of jacket, cut shield to 1/4”, strip tip 1/2” of center conductor,...

VAMPIRE B12 Male Banana Plug, 10-12awgThe #B12 may be crimped or soldered. Slide the color code cap over the outer jacket of the cable. Strip 1/2” of insulation, insert the exposed conductor into the connector, then crimp or solder the conductor in place...

VAMPIRE CM2F RCA Female Jack, outside nut Designed to be the finest connector available. The CM2F is gold plated and comes with all needed mounting hardware. It is designed to fit on chassis that have a .5” hole where the mount nut is on the outside...

VAMPIRE Vampire PCB2F/A Right-Angled RCA Female Jack pc-mount - Black An angled PCB mount connector made with a Teflon* dielectric. The #PCB2F/A has a brass base metal, a copper subplate, silver subplate, and a hard gold finish.  Specifications:RCA...

Vampire BP-0.5 Ground Post The Vampire BP.5 Grounding Post is built from one piece of hard brass (yes, this includes the nut!). First it’s plated in copper, then it’s plated in silver, and then it’s plated in gold to give DIYers the best possible medley...

VAMPIRE SPD Tinned Copper Spade Lug, 10-12awg These Spade Connectors from Vampire are gold-plated, over nickel-plated, over a brass base metal. DIY Tip: After crimping, slide the color coding over the connector extending onto the jacket of the cable...

VAMPIRE C9X Co-Axial RCA Male Plug (Satin/no logo), 9mm opening For 8.3-9mm diameter cables. Uses compression to insure proper RF shielding and strain relief. Slide nut on cable. Strip 3/4” of jacket, cut shield to 1/4”, strip tip 1/2” of center...

VAMPIRE BP-3/CE Gold-Plated Dual Binding Posts, 3/16" mounting shaft When it’s time to upgrade your Binding Posts this is a good choice if you don’t want to enlarge the mounting holes to accept the larger shanks on our upgrade posts. The BP-3/CE is a...

VAMPIRE BP-HEX Gold-Plated Dual Binding Posts, machined You’ll love the durable, no-nonsense construction of these binding posts. A single piece of hard brass transmits your music signal with full detail and clarity. It’s plated first in copper, then...

VAMPIRE HDS1 1/4" Gold Plated (Copper Base) Spade Lug, 6awg Made from pure copper, then gold plated. #HDS-1 will accept cables up to 6 ga., in size. Termination may be either solder or crimp. When crimping, be sure to crimp opposite the seam. The #HDS-1...

VAMPIRE PIN1 Male "rolled" Pin Connector, 10-12awg Gold plated speaker wire pin. Crimp connector to wire (10 ga. to 12 ga.), slide color coding over connector extending onto the jacket of the cable. Use a hand held hair dryer to shrink the color coding...

VAMPIRE BD Dual Male Banana Plug, 6 awg The #DB/2 is a cost effective double banana plug. It is a standard 3/4” spacing and will accept up to a 10 gauge cable.  Specifications:Male banana plug6awgCopper materialGold Plating

VAMPIRE BP-2/CE Gold-Plated Dual Binding Posts, 1/8" mounting shaft When it’s time to upgrade your Binding Posts this is a good choice if you don’t want to enlarge the mounting holes to accept the larger shanks on our upgrade posts. The BP-2/CE is a...

VAMPIRE "Wing Nut" Style Binding Post (Mark Levinson Version) 1-Red/1-Black This is a wingnut style RCA which means you can really crank it down. .500 square mount hole diameter. Gold plating(no nickel) over brass. Euro compliant. Specifications:.500...

VAMPIRE "Wing Nut" Style Binding Post  You’ll love the durable, no-nonsense construction of these binding posts. A single piece of hard brass transmits your music signal with full detail and clarity. It’s plated first in copper, then silver and gold to...