Vampire Collection

VAMPIRE CM1F RCA Female Jack (White only), inside nut Copper with direct gold plating.Designed to be the finest connector available. The CM1F is gold plated and comes with a gold plated ground lug. It is designed to fit on chassis that have used a...

VAMPIRE GS Male "solderless" Spade Lug, 10-12awg Crimp connector to wire (10 ga. to 12 ga.), slide color coding over connector extending onto the jacket of the cable. Use a hair dryer to shrink the color coding to size. Specifications:Male Spade...

VAMPIRE XLR-M XLR Male Plug, 10mm Opening Vampire’s premium XLR Connectors combine the warm conductivity of gold and copper with the slick appeal of a darker-than-night black finish. They come with strain relief clamps for an extra reliable hold and...

VAMPIRE 808 RCA Male Plug, 8.5mm opening Designed to offer the same mechanical integrity as the acclaimed #800C, but at a lower price. The #808 is machined from brass instead of OFC. The polished chrome barrel insures a proper fit for cables up to 8.5...

VAMPIRE C4X Co-Axial RCA Male Plug (Chrome/no logo), 4.2mm opening For 3.5-4.2mm diameter cables. Uses compression to insure proper RF shielding and strain relief. Slide nut on cable. Strip 3/4” of jacket, cut shield to 1/4”, strip tip 1/2” of center...

VAMPIRE CM2F RCA Female Jack (Red Only), outside nut Designed to be the finest connector available. The CM2F is gold plated and comes with all needed mounting hardware. It is designed to fit on chassis that have a .5” hole where the mount nut is on the...

VAMPIRE CMHEX RCA Female Jack (White only/no stripe), inside nut Designed to be the finest connector available. The CMHEX is gold plated with a Teflon dielectric. The CMHEX comes with a gold plated ground lug. Isolation washers are also included. It is...

VAMPIRE LRCA-7 RCA Male Plug, Locking 7mm opening The LRCA7 is designed to lock by compressing the ground crown to the chassis connector. The outer body controls the locking feature. Both coaxial and twinaxial cables are easily installed. To plug the...

VAMPIRE PC2V Dual Right-Angled Nickel-plated RCA Female Jack, pc-mount Entry level PC mount RCA connector. Brass base with gold plating and PBT dielectric.  Specifications:RCA Female JackBrass materialGold Plating

VAMPIRE XLR-CM XLR Male Jack Vampire’s own XLR. Copper alloy contacts are gold plated, obtaining the finest results from a balanced connector. Specifications:XLR Female JackCopper materialGold Plating

VAMPIRE GP Male "solderless" Pin Connector, 10-12awg Crimp connector to wire (10 ga. to 12 ga.), slide color coding over connector extending onto the jacket of the cable. Use a hand held hair dryer to shrink the color coding to size. Specifications:Male...

#504 VAMPIRE BD/2 Dual Male Banana Plug (Black only), 10awg

VAMPIRE "Wing Nut" Style Binding Post  You’ll love the durable, no-nonsense construction of these binding posts. A single piece of hard brass transmits your music signal with full detail and clarity. It’s plated first in copper, then silver and gold to...

VAMPIRE 557-Y RCA Male Plug (Yellow stripe), 5.6mm opening An entry level RCA. Gold plated over brass. Accepts a 5-6mm overall diameter cable.  Specifications:RCA Male Plug5.6mm openingGold platedBrass material

VAMPIRE 558 Male Banana Plug, 6-12awg Designed to accept 6-12 gauge cable. Strip 1/2” of conductor and insert into connector barrel. Tighten both set screws. 2 sets are provided, choose the appropriate length screws for the cable diameter. Screw on the...

VAMPIRE 807 RCA Male Plug, 7.2mm opening Designed to offer the same mechanical integrity as the acclaimed #800C, but at a lower price. The 807 is machined from brass instead of OFC. The polished chrome barrel insures a proper fit for cables up to 7.2 mm...

VAMPIRE B12 Male Banana Plug (Black only), 10-12awg The #B12 may be crimped or soldered. Slide the color code cap over the outer jacket of the cable. Strip 1/2” of insulation, insert the exposed conductor into the connector, then crimp or solder the...

VAMPIRE B8 Male Banana Plug (Black only), 8awg The #B8 may be crimped or soldered. Slide the color coded cap over the outer jacket of the cable. Strip 1/2” of conductor, insert stripped conductor into connector, then crimp or solder in place. Slide...